Dell OpenManage Storage

Plugin worked well. Below is the output. ./check_om_storage.pl --analyze --CMD1 parsed output: OpenManage version: 5.5.0 --CMD2--: /usr/bin/omreport storage controller -fmt ssv Controller PERC 4e/Di Controllers --CMD2 results: Got 6 controller lines Checking Controller No. 0: PERC 4e/Di --CMD3--: /usr/bin/omreport storage pdisk controller=0 -fmt ssv List of Physical Disks on Controller PERC 4e/Di (Embedded) Controller PERC 4e/Di (Embedded) ID;Status;Name;State;Failure Predicted;Progress;Type;Capacity;Used RAID Disk Space;Available RAID Disk Space;Hot Spare;Vendor ID;Product ID;Revision;Serial No.;Negotiated Speed;Capable Speed;Manufacture Day;Manufacture Week;Manufacture Year;SAS Address 0:0;Ok;Physical Disk 0:0;Online;No;Not Applicable;SCSI;136.62 GB (146695782400 bytes);136.62 GB (146695782400 bytes);0.00 GB (0 bytes);No;MAXTOR ;ATLAS10K5_146SCA;JNZY;J408BN9K;320;320;Not Available;Not Available;Not Available;Not Available 0:1;Ok;Physical Disk 0:1;Online;No;Not Applicable;SCSI;136.62 GB (146695782400 bytes);136.62 GB (146695782400 bytes);0.00 GB (0 bytes);No;MAXTOR ;ATLAS10K5_146SCA;JNZY;J407W95K;320;320;Not Available;Not Available;Not Available;Not Available 0:2;Ok;Physical Disk 0:2;Online;No;Not Applicable;SCSI;136.62 GB (146695782400 bytes);136.62 GB (146695782400 bytes);0.00 GB (0 bytes);No;MAXTOR ;ATLAS10K5_146SCA;JNZY;J4081FLK;320;320;Not Available;Not Available;Not Available;Not Available 0:3;Ok;Physical Disk 0:3;Online;No;Not Applicable;SCSI;136.62 GB (146695782400 bytes);136.62 GB (146695782400 bytes);0.00 GB (0 bytes);No;MAXTOR ;ATLAS10K5_146SCA;JNZY;J4080E4K;320;320;Not Available;Not Available;Not Available;Not Available --CMD3 results: Got 9 physical disk lines on controller 0 --CMD4--: /usr/bin/omreport storage vdisk controller=0 -fmt ssv Virtual Disk 0 on Controller PERC 4e/Di (Embedded) Controller PERC 4e/Di (Embedded) ID;Status;Name;State;Progress;Layout;Size;Device Name;Type;Read Policy;Write Policy;Cache Policy;Stripe Element Size;Disk Cache Policy 0;Ok;Virtual Disk 0;Ready;Not Applicable;RAID-5;409.86 GB (440087347200 bytes);/dev/sda;SCSI;Adaptive Read Ahead;Write Back;Direct I/O;64 KB; --CMD4 results: Got 7 logical disk lines on controller 0 Status of physical disk 0:0: Ok, state: Online, predicted: No, progess: Not Applicable Status of physical disk 0:1: Ok, state: Online, predicted: No, progess: Not Applicable Status of physical disk 0:2: Ok, state: Online, predicted: No, progess: Not Applicable Status of physical disk 0:3: Ok, state: Online, predicted: No, progess: Not Applicable Status of virtual disk 0: Ok, state: Ready, progress: Not Applicable, type: RAID-5 Checking Enclosures on Controller 0: --CMD5--: /usr/bin/omreport storage enclosure controller=0 -fmt ssv Enclosure(s) on Controller PERC 4e/Di (Embedded) ID;Status;Name;State;Connector ;Target ID;Configuration;Firmware Version;Service Tag;Asset Tag;Asset Name;Backplane Part Number;Split Bus Part Number;Enclosure Part Number;SAS Address;Enclosure Alarm 0;Ok;Backplane;Ready;0;6;Not Applicable;1.0 ;61900ER;Not Applicable;Not Applicable;Not Applicable;Not Applicable;Not Applicable;Not Applicable;Not Applicable --CMD5 results: Got 5 enclosure lines Status of enclosure 0 (Backplane): Ok, state: Ready Checking Connectors on Controller 0: --CMD6--: /usr/bin/omreport storage connector controller=0 -fmt ssv List of Connector(s) on Controller PERC 4e/Di (Embedded) ID;Status;Name;State;Connector Type;Termination;SCSI Rate 0;Ok;Connector 0;Ready;SCSI Channel RAID Mode;Wide Terminated;Ultra 320M SCSI 1;Ok;Connector 1;Ready;SCSI Channel RAID Mode;Wide Terminated;Ultra 320M SCSI --CMD6 results: Got 5 connector lines Status of connector 0 (Connector 0, SCSI Channel RAID Mode): Ok, state: Ready Status of connector 1 (Connector 1, SCSI Channel RAID Mode): Ok, state: Ready Checking Batteries on Controller 0: --CMD7--: /usr/bin/omreport storage battery controller=0 -fmt ssv Battery 0 on Controller PERC 4e/Di (Embedded) Controller PERC 4e/Di (Slot Embedded) ID;Status;Name;State;Recharge Count;Max Recharge Count;Predicted Capacity Status;Learn State;Next Learn Time;Maximum Learn Delay 0;Ok;Battery 0;Ready;1;1100;Not Applicable;Not Applicable;Not Applicable;Not Applicable --CMD7 results: Got 6 battery lines Status of battery 0: Ok, state: Ready Result: 0 STORAGE: OK [ Ctrl 0 (PERC 4e/Di is Non-Critical (Degraded: firmware mismatch: running: 521S, required: 522D)) ]